Grundfos CR 10-2 H-G22-A-E-HQQE (97679206)
Product ID: 97679206
Request Price and Availability
Grundfos CR 10-2 H-G22-A-E-HQQE (97679206)
Grundfos CR 10-2 H-G22-A-E-HQQE (97679206)
Horizontal end suction pumps typically mounted on baseplates. The end suction design enables the pump to be installed horizontally in traditional, end suction design piping where the pump has an axial suction port and a radial center line discharge port. This design allows “back pull-out” capability. This means the pump usually can be easily serviced without removing the volute from the pipe system.
Pumps can be selected that meet ASME B73.1 dimensional standards for suction and discharge piping as well as many of the baseplate dimensional standards. CR-H pumps do not fully comply with the ASME B73.1 specification.
| Controls: | |
| Frequency converter: | None |
| Pressure sensor: | N |
| Liquid: | |
| Pumped liquid: | Water |
| Liquid temperature range: | -20 .. 120 °C |
| Selected liquid temperature: | 20 °C |
| Density: | 998.2 kg/m³ |
| Technical: | |
| Pump speed on which pump data are based: | 3466 rpm |
| Rated flow: | 12 m³/h |
| Rated head: | 21.2 m |
| Pump orientation: | Horizontal |
| End suction pump (Yes/No): | Y |
| Shaft seal arrangement: | Single |
| Primary shaft seal: | HQQE |
| Code for shaft seal: | HQQE |
| Approvals on nameplate: | CURUS,NSF/ANSI 61 |
| Curve tolerance: | ISO9906:2012 3B |
| Materials: | |
| Base: | Cast iron |
| EN 1561 EN-GJL-200 | |
| ASTM A48-25B | |
| Impeller: | Stainless steel |
| EN 1.4301 | |
| AISI 304 | |
| Bearing: | SIC |
| Installation: | |
| Maximum ambient temperature: | 60 °C |
| Maximum operating pressure: | 16 bar |
| Max pressure at stated temp: | 16 bar / 120 °C |
| 16 bar / -20 °C | |
| Size of inlet connection: | 2 inch |
| Size of outlet connection: | 2 inch |
| Pressure rating for connection: | PN 16 |
| Flange rating inlet: | 150 lb |
| Flange size for motor: | 56C |
| Electrical data: | |
| Motor standard: | NEMA |
| Motor type: | 80BA |
| Rated power - P2: | 1.1 kW |
| Power (P2) required by pump: | 1.1 kW |
| Mains frequency: | 60 Hz |
| Rated voltage: | 3 x 208-230YY/460Y V |
| Service factor: | 1.15 |
| Rated current: | 4,70-4,60/2,30 A |
| Starting current: | 720-800 % |
| Cos phi - power factor: | 0.84-0.75 |
| Rated speed: | 3450-3480 rpm |
| IE Efficiency class: | NEMA Premium / IE3 60Hz |
| Number of poles: | 2 |
| Enclosure class (IEC 34-5): | 55 Dust/Jetting |
| Insulation class (IEC 85): | F |
| Motor No: | 96905316 |
| Others: | |
| Net weight: | 60 kg |
| Gross weight: | 107 kg |
| Shipping volume: | 0.37 m³ |
category
- Inline multi stage pumpsIn-line multi-stage pumps are used in installations in which a high head is needed. Several impeller stages are connected in series and the inlet and outlet are on the same level. In-line multi-stage pumps are used for water supply, water treatment and almost any industrial solution including those for aggressive liquids.