Filmtec RO-390-FF

Filmtec RO-390-FF membrane Seawater RO Elements for Sanitary Applications reverse osmosis membrane elements deliver high flux and outstanding quality water for applications requiring sanitary grade membrane elements.
Product name	RO-390-FF
Part number	116314 / 100608
Nominal Active Surface Area	390 (36) ft2 (m2)
Maximum Operating Pressure	600 psi (41 bar)
Permeate Flow Rate	10,800 (40.9) gpd (m3/d)
Stabilized Salt Rejection	99.5 %
1. RO-4040-FF was previously named BW30-4040-LW. 2. RO-390-FF replaces BW30-380-LW and BW30-8040-LW. 3. Permeate flow and salt rejection based on standard conditions: 2,000 ppm NaCl, 225 psi (16 bar), 77°F (25°C), pH 8 and 15% recovery. 4. Minimum stabilized salt rejection is 98.0%.
Membrane Type	Thin-Film Composite (Filmtech)
Maximum Operating Temperature	113°F (45°C)
Maximum Feed Flow Rate	6 (1.4) gpm (m3/h)
Maximum pressure drop	15 psig (1.0 bar)
pH Range, Continuous Operation	3-10
pH Range, Short Term Cleaning	1-12
Maximum Feed Silt Density Index	SDI 5

Important Information:

Proper start-up of reverse osmosis water treatment systems is essential to prepare the membranes for operating service and to prevent membrane damage due to overfeeding or hydraulic shock. Following the proper start-up sequence also helps ensure that system operating parameters conform to design specifications so that system water quality and productivity goals can be achieved. Before initiating system start-up procedures, membrane pretreatment, loading of the membrane elements, instrument calibration and other system checks should be completed. Please refer to the application information literature entitled “Start-Up Sequence” (Form No. 609-02077) for more information.

Operation Guidelines:

Avoid any abrupt pressure or cross-flow variations on the spiral elements during start-up, shutdown, cleaning or other sequences to prevent possible membrane damage. During start-up, a gradual change from a standstill to operating state is recommended as follows: Feed pressure should be increased gradually over a 30-60 second time frame. Cross-flow velocity at set operating point should be achieved gradually over 15-20 seconds. Permeate obtained from first hour of operation should be discarded.

General Information:

Keep elements moist at all times after initial wetting. If operating limits and guidelines given in this bulletin are not strictly followed, the limited warranty will be null and void. To prevent biological growth during prolonged system shutdowns, it is recommended that membrane elements be immersed in a preservative solution. The customer is fully responsible for the effects of incompatible chemicals and lubricants on elements. Maximum pressure drop across an entire pressure vessel (housing) is 50 psi (3.4 bar). Avoid static permeate-side backpressure at all times.

Notice: The use of this product in and of itself does not necessarily guarantee the removal of cysts and pathogens from water. Effective cyst and pathogen reduction is dependent on the complete system design and on the operation and maintenance of the system. Notice: No freedom from any patent owned by Seller or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for determining whether products and the information in this document are appropriate for Customer’s use and for ensuring that Customer’s workplace and disposal practices are in compliance with applicable laws and other governmental enactments. Seller assumes no obligation or liability for the information in this document. NO WARRANTIES ARE GIVEN; ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.

The full-fit configuration minimizes stagnant areas and is optimal for applications requiring a sanitary design. All components comply with FDA standards

Lenntech can also help you with similar brackish and seawater filters or filtration systems for optimum water purification and liquid filtration. Also we can provide other Filmtec type replacement membranes
Please feel free to contact us for any information on reverse osmosis water filters.